Quik Posted February 11, 2007 Report Share Posted February 11, 2007 this right now is my 408..... L92 heads milled .030 cosmetic .040 L76 intake SVO 42s NW 90mm tb Lunait forged 408 244/248 612/615 112+2 11.2 cr meizere electric water pump all accesorie brackets powdercoated SLP underdrive pulley 97/98 vette fuel rail ARP studs 04 new 6.0 block Fbody accessories custom vette fuel rail covers LS6 valley cover PCV delete a very very similar setup just recently put down 551rwhp and 538rwtq thru 1 3/4 headers and dual 2.5 exhaust with stock air intake ill be running 1 7/8 stepped to 2" and dual 3" exhaust with custom 4" air intake along with a electric water pump...im hoping to see similar numbers of 550+ rwhp Quote Link to comment Share on other sites More sharing options...
ItsJac Posted February 11, 2007 Report Share Posted February 11, 2007 very nice...Look like its going to be a nice running engine...It going in the 240 for a new epsidoe of pinks...LOL Quote Link to comment Share on other sites More sharing options...
Quik Posted February 11, 2007 Author Report Share Posted February 11, 2007 very nice...Look like its going to be a nice running engine...It going in the 240 for a new epsidoe of pinks...LOL haha, yep got me there nah its going in a 02 RCSB with a proshifted T56 and a 14 bolt with 4.88s gears Quote Link to comment Share on other sites More sharing options...
gixxerrider Posted February 11, 2007 Report Share Posted February 11, 2007 looks good. Whens it going to run? Quote Link to comment Share on other sites More sharing options...
Quik Posted February 11, 2007 Author Report Share Posted February 11, 2007 looks good. Whens it going to run? good question...tomorrow i plan on mounting my Mcloud bellhousing and my Proshifted trans...then i need to rewire my harness so it works with the 6speed and need to re wire my map sensor then need to come up with cash for the exhaust and other htings....biggest thing is unemployment right now is hurting the budget Quote Link to comment Share on other sites More sharing options...
04CHASE Posted February 11, 2007 Report Share Posted February 11, 2007 nice components, what does the pcv delete invole and what are the benefits? Quote Link to comment Share on other sites More sharing options...
Quik Posted February 11, 2007 Author Report Share Posted February 11, 2007 nice components, what does the pcv delete invole and what are the benefits? noting really as in parts. a few caps to cap off all lines goign to intake. then i ran a hose from the LS6 valley cover to the valve cover. capped off the back on same valve cover. then installed 2 breathers. one on passenger side and one in driver side benefits stops oil from being sucked into the intake Quote Link to comment Share on other sites More sharing options...
Quik Posted February 12, 2007 Author Report Share Posted February 12, 2007 heres the Liberty proshifted T56, McCloud bellhousing, and a Ram VDS clutch,stock Hurst Ram VDS Clutch System w/ 900 series disk, pressure plate & billet steel flywheel, rated to 700 hp, 1998-2002 LS1 F-body, 1997-2004 C5 Corvette, 2004-2005 GTO Quote Link to comment Share on other sites More sharing options...
Quik Posted February 20, 2007 Author Report Share Posted February 20, 2007 heres some more pics....this is a mock up trans and block. i still have some finish triming up to do on the underside of truck and hit it with some paint to prevent rusting...the rubber booty is from a fbody. also that is the a stock 5speed crossmember...i did all cutting from up in the cab area. tomorrow ill go and trim since i see i got some i need to show attention to Quote Link to comment Share on other sites More sharing options...
Quik Posted February 20, 2007 Author Report Share Posted February 20, 2007 Quote Link to comment Share on other sites More sharing options...
gixxerrider Posted February 20, 2007 Report Share Posted February 20, 2007 looks good. how is the 06 rear? Quote Link to comment Share on other sites More sharing options...
Quik Posted February 20, 2007 Author Report Share Posted February 20, 2007 plan on swapping 14 bolt in this week hopefully my motor and trans can go in any day now just need to find the wiring diagrams so i can finish up my harness Quote Link to comment Share on other sites More sharing options...
SS_bnoon_SS Posted February 20, 2007 Report Share Posted February 20, 2007 Very nice! Color me green with envy!!! How's the unemployment going? The free time's got to be nice for the project, but no funds coming in sucks bad. I was out of work for 3 months a couple of years ago and just barely got by... Layoffs and company cutbacks always seem to happen to me right after I spend a chunk of money too... Quote Link to comment Share on other sites More sharing options...
Quik Posted February 20, 2007 Author Report Share Posted February 20, 2007 Very nice! Color me green with envy!!! How's the unemployment going? The free time's got to be nice for the project, but no funds coming in sucks bad. I was out of work for 3 months a couple of years ago and just barely got by... Layoffs and company cutbacks always seem to happen to me right after I spend a chunk of money too... it sucks, the time is good to have but no funds suck. i spent the intial money on this combo back in dec now being out of work sucks...kinda wish i had the cash now instead of the parts. ohwell ill get by hopefully soon Quote Link to comment Share on other sites More sharing options...
SS_bnoon_SS Posted February 20, 2007 Report Share Posted February 20, 2007 Very nice! Color me green with envy!!! How's the unemployment going? The free time's got to be nice for the project, but no funds coming in sucks bad. I was out of work for 3 months a couple of years ago and just barely got by... Layoffs and company cutbacks always seem to happen to me right after I spend a chunk of money too... it sucks, the time is good to have but no funds suck. i spent the intial money on this combo back in dec now being out of work sucks...kinda wish i had the cash now instead of the parts. ohwell ill get by hopefully soon Didn't you work for a wrecking yard or something like that? I know you had access to used parts at one time... Heck, I just sent a new member here to you for a TB converter 'cause I remembered you had some for sale a while back... Man, what's the world coming to when a famous "Pinks" winning driver loses his job? Sorry, bad joke... Let us know what it is you do, or want to do. Maybe we can help. I've found several good leads in the past just by mentioning it on the boards I frequent. Networking with people does work!!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.