[Donut Style Exhaust Gasket for OBX headers]

OBX header pn 501-1310-6.

I need 2 Donut Style Exhaust Gasket. Anyone have a part number or dimension for replacements? I sent a messgae to OBX no reply yet.

Thanks

[Front axle went from howling to banging & popping.]

Thanks for the Info!

[Front axle went from howling to banging & popping.]

Did you get the rebuild done by DTS? What did it cost? how long did it take? I'm needs a rebuild before this winter.

[Front Differential Rebuild Kit & Gears]

If I could afford it I would just go OEM all the way. I don't think that you could find "better", cheaper maybe, but not better, and it takes the guess work out of it.

 

Good luck. You going to rebuild it yourself?

Do you have a part number for OE front axle asby?

[Headlight Advice]

any particular vendor?

[Rearend swap]

Yes you would need to change your front diff gearing also.

[WTB: Stock exhaust]

Close please...Thanks Time2Kill

[WTB: Stock exhaust]

No idea, but he said he found one on the last page. Maybe your the guy hes talking about.

10-4

[Diagnosing brake sensor issue]

To diagnosis which one is bad. A good wheel speed sensor will typically produce an AC voltage reading of 50 to 700 mV when the wheel is turning one revolution per second. Hook a volt meter set on AC to the sensor end of the connector. Spin the tire and measure the voltage. Lower than 50mV is your bad sensor.

[Help ID my new trucks headers]

if you can afford it , do header studs makes for a way easy install.

Thanks I'll put them on my list of things to do.

[WTB: Stock exhaust]

I found exhaust local to me. Thanks Guys!

[WTB: Stock exhaust]

Still looking for a muffler back exhaust.

[Help ID my new trucks headers]

obx for sure, just dont go with magnaflow i had them with my obx and they droned bad. another thing is you might want to replace those bolts before they start breaking off.

The header bolts? What would you suggest?

[Anyone on here own my old truck??]

Does anyone have a email address for rojo 143? I would like to get more infomation on the truck I just bought.

It used to be Justin's. Thanks in advance.

 

Wade

[Anyone on here own my old truck??]

I have your old truck! I sent you a PM.

[WTB: Stock exhaust]

Cool thanks a video would be great.

[WTB: Stock exhaust]

Must be fake cats. Just pick up the truck with no information.

Good to know on the stock exhaust and no drone.

xr4tic where are you located in Michigan? I would like to hear your truck maybe copy your setup.

[Anyone replace all their brake lines?]

The inline tube kit is $200 for SS Lines and pre-bent,

[Help ID my new trucks headers]

Corsa all the way!

Corsa will bolt on to OBX Catted LT headers?

[WTB: Stock exhaust]

The truck has OBX LT Catted headers.

So I guess I need to figure out what I need to do to quite it down and get rid of the drone on the Highway.

[Member since 2002 first post LOL]

Thanks for the welcome guys.

Still working on what all the mods that it has. Looks like OBX LT catted headers. I bought it from a dealer with no information.

Anyone from Detroit area familiar with this truck? I not driving too much until I know it was tuned properly.

[Help ID my new trucks headers]

Looks like OBX to me.

Thanks... I think you are correct. What is a good sounding no drone Cat back to go with these?

[Obx headers are in]

What are you doing for the rest of your exhaust?

[Help ID my new trucks headers]

Anyone want to guess who makes these Catted LT Header and crossover?

Here's the drivers side.

 

[WTB: Stock exhaust]

Long shot but anyone have a stock system laying around that they don't want?

Near Michigan would be helpful. LMK