rickgt1

here is the curb rash pic. and i'm down in Parris Island

Need to sale, these are just sitting in my garage. They are 22 inch Diamo machined w/black wheels. Tires are Nitto's 420's with about 85% tread left on them. Im askin $1200 plus shipping. One wheel has some minor curb rash, all others are perfect. Im located in South Carolina.

I have (4) 22 inch Diamo wheels wrapped in Nitto 305X40X22. Traded my SSS and need to get these sold. Asking $1500. i'm located in SC

I installed my new AVH-p6000dvd, but for some reason I could not get power to it using the wiring harness. The way i got my ACC is from the fuse box and i got my battery power from tappin in behind the cigertte lighter. Is this safe? Is their someting else I could do? Im using the APEXX GMOS whatever wiring harness, i thought mabye i had a bad factory harness.

Im instslling a Pioneer AVH P6000DVD, and im not sure where to run the parking brake wire too. IM seeing a LT. Blue wire on the parking brake. is this where it goes. Rick

Can someone please tell which wire do i tap into so i can play DVD's while driving. Thanks

thats sounds good. thanks. but what about the truck pulling to the left?

it was on both front tires. I have 90,000 and I drive about 200 miles per week, all highway on twisty mountain roads.

outer edge. I ve been to 2 different shops.

I have had a alignment every two weeks now for a month and just put on new tires. The alignment was dead center. It still pulls to the left and I don't know what it could be. it's been doing it for a long time. it made my last set of tires wear uneven. I don't want this to happen to my new set of tire. I'm gettin ready to move and I will be driving cross county. If any body has any suggestions please chime in. Thanks

http://farm4.static.flickr.com/3575/351987...77f4e99bd_b.jpg http://farm4.static.flickr.com/3636/351990...3120c49df_b.jpg http://farm4.static.flickr.com/3547/352081...da4925be5_b.jpg

USMC 16yrs Active duty Here. Hey turbocop Im heading to Parris Island in August. It will be nice to see another member.

I leaning towards these wheels. Akuza Drift 455 Black 22".

i am in northern California.

I need to get rid of this thing. It's taking up too much room in the Garage. It's in one peice from the muffler to the stock tip. $100.00 plus shipping.

I lost one of my center caps. Anybody know a place other than the Dealer for a replacement? GMPartsDirect wants over $100 dollars for one. Ebay has replica's without the chevy logo. Thamks

I want to get Hawk Ceramic pads for my 03 SSS. Anybody got these ? What is the part number ? I orderd some from Summit, but they turned out to be the wrong pads. I have seached the sight but didn't find much. Thanks

I've had my truck stall on me several times this past week while driving at low MPH. At the same time it is also only idleing at @ 500 RPM's. I have 77k miles and I've recently had the Battery, Plugs/wires and fuel filter replaced. I'm not much of an engine guy, so any help or suggestions would be great. Rick

need help with the step by step install. the instruction that came with it are kinda difficult to understand. any help would be great. Thanks Rick

I need the part number for the plastic peice that covers the seat controls for the driver side seat. I took it off and searched gmpartsdirect and got nothing. I also need the part number for the black plactic peice that is on the top of the back bumber. Thanks

Can the factory xm antenia be used on a aftermarket radio? I am installing an Alpine IVA-W205 and want to use my factory xm antenia, if their is an adapter, can someone help with the part # or a link to the product. Thanks

does anybody know why my front driver side heated seat keeps cutting out? it will kick on for about 30sec-1min and then kicks off. Thanks Rick

I have a buddy who has a 93 yukon and needs to put in a stereo, but has no factory wiring harnes. What can i do to instal his new system? Im not to sure where to get a good power or ground from. If anybody could sheed some light on this situation please don't hesitate. Thanks

I have a constant static noise coming from the Onstar spreaker above the drivers head. I dont even have Onstar. The noise is driving me crazy, any suggestions? Rick

I got it working. I had cut the input jacks of the speaker wires and just connected them staight to the factory wire harness. So once I attached them back on everything is all good.