onebadmax Posted February 8, 2014 Report Share Posted February 8, 2014 Installing bump stick tomorrow morning! Wish me look guys. Quote Link to comment Share on other sites More sharing options...
Muggs Posted February 8, 2014 Report Share Posted February 8, 2014 Nice bro, which cam did you get? Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 8, 2014 Author Report Share Posted February 8, 2014 Comp 226/230 .598/.600 114lsa. Not sure which lobes I got though. The numbers don't work out for a XER lobe. Doesn't say on the box. It was a custom grind for me. Quote Link to comment Share on other sites More sharing options...
Downeast Johnny Posted February 8, 2014 Report Share Posted February 8, 2014 Enjoy your project man. Hope it all goes fast and easy. Love the avatar, BTW. Quote Link to comment Share on other sites More sharing options...
RockHead Posted February 8, 2014 Report Share Posted February 8, 2014 Make sure you get a video! ! Sent from my SCH-I545 using Tapatalk Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 8, 2014 Author Report Share Posted February 8, 2014 Enjoy your project man. Hope it all goes fast and easy. Love the avatar, BTW. Nortech 392. Quad 300s. We went 168 miles offshore that day. Put 450 total miles on the boat chasing yellowfin. Quote Link to comment Share on other sites More sharing options...
Downeast Johnny Posted February 8, 2014 Report Share Posted February 8, 2014 Nortech 392. Quad 300s. We went 168 miles offshore that day. Put 450 total miles on the boat chasing yellowfin. I was guessing four. Looks even more serious than the Kingfish tournament runners round here. Looks like a lot of fun, (and fuel). Quote Link to comment Share on other sites More sharing options...
canadianVRss Posted February 8, 2014 Report Share Posted February 8, 2014 Have fun, that cam is very close to mine. Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 8, 2014 Author Report Share Posted February 8, 2014 Well having difficulty getting stock can out. Pin magnets don't work worth a ****. Going to try and turn old pushrods into magnets instead. This is a bitch. Quote Link to comment Share on other sites More sharing options...
JC03SS Posted February 8, 2014 Report Share Posted February 8, 2014 Nortech 392. Quad 300s. We went 168 miles offshore that day. Put 450 total miles on the boat chasing yellowfin.Burnt about 3k in gas too lol. Good luck with the install. Wooden 5/16 Dow rods work well to hold up the lifters. Quote Link to comment Share on other sites More sharing options...
canadianVRss Posted February 8, 2014 Report Share Posted February 8, 2014 Well having difficulty getting stock can out. Pin magnets don't work worth a ****. Going to try and turn old pushrods into magnets instead. This is a bitch. Take your rocker arms off. Then rotate the cam. The lifters should be held in the lifter trays. Then keep the cam gear installed and use it to pull the cam out. It makes it even easier if you can rotate the cam gear while pulling the cam out. Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 9, 2014 Author Report Share Posted February 9, 2014 Alright guys, don't fool around with pin magnets or dowel rods, they are not necessary in most cases. Just spin the cam over and let the trays hold them up. You can even stick a pushrod back in and test to see the holding power of each lifer. Obviously your stock cam MUST be in place for this test. Everyone of my lifters needed 5lbs of force to push them back down to the cam lobe surface. Truck is back together now, tuning tomorrow. Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 9, 2014 Author Report Share Posted February 9, 2014 Burnt about 3k in gas too lol. Good luck with the install. Wooden 5/16 Dow rods work well to hold up the lifters. Haha yeah we burnt 560gal of fuel that day. I had 7 buddies with me so we split fuel, came out to like 250 per person. We fished offshore for two days straight, that's the cheapest you'll be able to fish out that far for that long. Quote Link to comment Share on other sites More sharing options...
JC03SS Posted February 9, 2014 Report Share Posted February 9, 2014 Haha yeah not a bad deal. Good you got the cam in and no probs. lots of people just turn the cam when the lobes push the lifters up they usually stick. Heard of them dropping and your screwed. Get er tuned up and let us know how she runs. Quote Link to comment Share on other sites More sharing options...
onebadmax Posted February 9, 2014 Author Report Share Posted February 9, 2014 It runs it runs. But I'm having a problem keeping it running when coming to a stop. More tuning to do. Sounds like a sewing machine haha. Click click click. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.