firehawknwv

Ive thought about getting one of these so I may pick this up off of you. However I went to get a PCV valve to replace mine on my truck since IM going through and tonig routine stuff and they told me that it dont call for one. So since the pic above is on the drivers side there must be a vlalve there for the can to be hooked up right?

How much is the replacement shaft? My 02 s10 Xtreme had the same problem.

Thanx man!They seem to be a direct plug n play.....

Im thinkning it could also be the notorious noise from our steering that many of us get. If its not those bushings and you cant find it anywhere elese it may be this. You can help it out by ubolting the knuckle in your stering shaft and slide the upper shaft in and out a few times. Some guys have referred to this in other posts as jerking their truck off,lol.

Looking good man.

Haha thats ok man it happens when you have green brain, lol. Joking. Ok, I saw that pic and thought thats what you did. So I wont use the harness and do what you did. Now I need to find me some bigger injecors so Ill have that ready for future mods also.

Got pics of the door sill plates

By just splicing the stock wires to the new harness?

Yea Ive seen taht car posted somewhere before. I think its a bit dumb, lol. I couldnt imagine how rough it would ride and how slow ud have to drive it.

Well I ordered the pump today from Magnacharger and got the 04 and up kit. He asked me if I need the wiring harness for it also cuz it wont match up to the harness thats on it so I got that to. Did you guys use the wiring harness?

Did you get Balasts with the bulbs cuz ull need those to plug into the factory wiring harness.

Well you can get them from V-LEDs but I ordered mine off Ebay cuz I didnt know of the company at the time. I got all of mine in white.

Dang that would be a great deal man. Im just wanting another set to PP and build on with installation of a TBSS intake.

Man if i had the 800 to spend on it Id pick up the Tranny right now.

I definately like the spoiler decal. ive not seen viyl embossed like that. Unless you just but the words with different vinyl underneath the main piece. Im curious as to how that was done. Now the wheel decal is different but not for me but if you like it then keep it by all means.

LOL nice find

Thats it startem into cars young, lol.

That is a nice tip but Im going to b running dual exhast with a x pipe. So I will need two single tips.

I came acrossed these 317 heads on ebay and they seem to look fine to me but I want others opinions. http://cgi.ebay.com/ebaymotors/GM-5-7-6-0-CYLINDER-HEADS-LS1-LQ4-317-_W0QQcmdZViewItemQQhashZitem4a9fe912f8QQitemZ320510431992QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

I am a steelers fan myself but that is ridiculous as hell.

When I searched them on ebay only marine tips came up, lol.

Hey guys where is a good place to get Corsa tips from. I can find their bolt on tips but wanted normal weld ons thougt I kow I could weld on the bolt on tips. I know most of there tips are slashe cut so I planned to drop them wher mine is now in the rear quarter when I do the new exhaust install. I will more than likely have them stepped when sticking out cuz I think tha tlooks really cool. Thanx chris

I dont see how cuz Norcal sold me a 2/3/4 kit and its on the lower hole setting for a 3in. drop. Do you happen to know an average fender heigth for a 3in drop in the rear.

Im not too partial to it myself but it is an intereting way of 2-toneing. The wheels is a definate must go.

I swear those of you wtih a 2/3 drop looks higher in the back than mine does for some reson. Mine is 2/3 and I can only get like 2 fingers in my wheel well and it rubs form time to time. im running 22's and looks like some of you are. I wonder why mine looks lower than 3" in the back. Sorry to thread jack her ebut I just wanted to point it out.