HDMLNIUM

Thanks guys, she is getting there.. Charlie, not as fun as the Lightning was, but as she gets quicker it gets closer. My son is doing great, he is 4 years old now and a lot of fun.. Bill

Sounds fair to me, you take paypal??

No reply, to low of an offer? Just let me know what you want for the kit and I will see if it is something I can do.. Thanks, Bill

I'll toss you a price, how about $350.00 shipped to 04074?? Thanks, Bill

What does the kit come with? Spindles, hangers, shackles?? Thanks, Bill

Well we went to the track last night. I made three passes and the were all in the 12's. First pass was against a Red Silverado SS (Jeff it was nice to meet you) and I ran a 12.91 to his 15.06. Second run (Video below) was against a Yellow z06 Corvette and I ran a 12.880 to his 13.61.. And the last run of the night was against another Vette and I ran a 12.887 to his 11.19.. Slip looked like this; 60'..........1.783 330'.........5.234 1/8...... ....8.148 MPH........84.15 1000'......10.701 1/4.........12.880 MPH........103.40 Video............ http://media.putfile.com/12880-10340

I will take it after Holty.... PM me when your done... Bill

I'll take it.... Bill

I use 4hi at the track and haven't had any problems yet. 13.20's at just over 100 mph in 4-Hi in the 1/4 mile and 1.8's 60' times. Not to bad for running in 4-Hi, give her a shot and you will like it... Bill

I did the install a couple weeks ago. If you are talking about the very inside bottom bolt than there isn't one. There is only three top and two bottom bolts, remove them and then just give it a little wack with a rubber mallet and the J-tube will come right off.. Bill

Richard, I will take the transmission, shipped to 04074 Thanks, Bill

Nice info and write up Mr. P............ Bill

I am running the stock 3.40 for now.. Bill

Well I went to the track last night with a few friends. Had a good time and I now have a new personal best with the truck. I will post my best run and the videos of both of the 13.2 runs... enjoy Bill 60'..........1.870 330'.........5.427 1/8..........8.417 MPH........82.35 1000'......11.027 1/4.........13.263 MPH........100.57 http://media.putfile.com/13263 http://media.putfile.com/13267

Depending on the weather I am planning on going to New England Dragway tomorrow night. Just thought I would through it out there to see if anyone else is planning on going.. Bill

I just put on a bigger heat exchanger for the Radix. Now I want to use the heat exchanger that came with the Radix kit for the tranny cooler. I searched last night and couldn't find the post about doing this. If I remember right someone did this and use some fittings to go onto the factory cooler lines and branched up to 5/8" hose fitting. I need some help trying to track down the parts I need to do the swap Thanks for any help or ideas with this... Bill

Thanks, added the video to the first post.. Bill

Thanks guys, she is getting there... I also have a small 15 second video clip of the run against a Mustang if anyone can host it..? Thanks again, I will run my 17's next time to see if I can shave a little more off the time.. Bill

I just got back from the track and made a couple of passes. A 13.496 at 98.38 and a 13.541 at 98.13 Both runs were made in 4HI... My best run looks like this; 60'.......1.893 330......5.538 1/8.......8.557 MPH.....82.46 1000'....11.212 1/4.......13.496 MPH......98.38 The video clip... http://media.putfile.com/134969838 Here is a pic of the launch... Bill

Just checking in to see if anyone will be going. I will be there and will be trying to break into the 13 second club... Hope to see some trucks there.. Bill

Thanks for the help guys.. I have an appointment tomorrow to get a new tune. I will drive her easy there as I have already set off a couple codes for being too rich. Bill

Well we finished up the install at about noon, pretty straight forward job with great instructions. I had a friend of mine give me a hand and it took us about 8 to 9 hours to do the whole job taking our time. I am going to go get the truck tuned tomorrow and then I will give my impressions after I get home. Here are a few pics of her all done.. Bill

Well I started doing the install this afternoon. I figure I still have two or three hours left of work to finish her up in the morning. My problem so far is that the Superchips programmer wouldn't tune it. It had an error code of 036 and I won't be able to get a hold of anyone there until Tuesday. I have a Westers tune in my truck now and I am going to get it retuned for the Radix on Monday. My main question is is this truck going to run ok to drive it a couple hours on the highway to get to where it will be tuned. I know I can't beat on it or anything but will it run ok if I baby it there?? Thanks for any help.. Bill

Well I got home from work today and sure enough there were two boxes here waiting for me. My Radix kit came in, that is great so now I know what I will be doing this Sunday.. Bill

Thanks guys, believe it or not I already lowered it 4" in the back by removing the blocks and using 2" lowering shackles, I also cut one nub off all four bump stops and de-cranked the t-bars for about a 2" drop in the front. I think I am going to order some hangers and some spindles and drop her down a couple more inches. I took the bull bar off to the other day so here are a couple more pics without it.. Bill