[8 Rib Pulley Setup]

ok thanks

[8 Rib Pulley Setup]

yeah the tensioner that came with my maggie does bounce around abit but i havnt seen anything to replace it with i figure the new pulleys would help out a bit . has any one tried this place ?

http://www.innovatorswest.com/store/index....mp;productId=50

[8 Rib Pulley Setup]

i am thinking of changing to an 8 rib set up there is a fair amount of belt dust around my pulleys . is it worth changing to the 8 rib or stick with 6 rib and just change the blower pully ? i was looking at the reichard pulleys its alot for a set of pulleys but i guess if it will solve the problem it would be worth it

[B&b Exhaust]

this clip is from when my truck had b&b true dual side exit

http://videos.streetfire.net/video/Ford-Ya-Later_164021.htm

as is this one

http://videos.streetfire.net/video/silverado-ss_155066.htm

i had to change it cause it got damaged so i went with corsa sport the corsa is WAY louder but the b&b has a sweet rumble

this is the corsa

http://videos.streetfire.net/video/corsa-s...long_176362.htm

http://videos.streetfire.net/video/silvera...clip_180359.htm

the second clip doesnt do it justice it is very loud with the corsa if you don't want to much attention the b&b is the better way to go

[Redline ?]

my cam specs are listed in this thread

http://www.silveradoss.com/forums/index.ph...47037&st=15

yeah i dont think the maggie would be any good over 6400 or so

[Redline ?]

i was just wondering what other people with built engines are setting for redline ? i am at 6100 right now but think i might go higher would it be safe to rev to 6600 or so ? keep in mind i have heads and cam and blower on a 408

[Blew My 4l65 For The 2nd Time]

i used the performance transmissions 4L80e kit altho i used my own trans . kit was great a little tuning and works great until i blew up the 4l80e but after another rebuild it has worked great

[Magna 2300 Tvs]

well not faster top speed ( i hear 190mph for the cts-v ) but thru the 1/4 would be cool and there will be videos soon of my truck the way it is , cause that corsa exhaust is WAY to loud lol

[Magna 2300 Tvs]

fortunatly i already have a house lol . and my 2009 cts-v will be here in late october but i want my truck to be faster lol

[Magna 2300 Tvs]

when i talked to a shop about a twin turbo setup from aps they were around $18 000 and i don't want sts because of where i live

[1900 Tvs]

magna lists the 1900tvs at $6800 for the full kit for 99-07 then you gotta pay someone to put it in

[Magna 2300 Tvs]

i know it wont be cheap . i have a friend with a procharger setup thats why i don't want to go that route , can't do the same thing hahaha and when i talked to magna they said the 1900 would be at its limit to feed my engine . turbo is an idea but all the kits i have seen are big bucks since i am already set up to run the maggie .

[Magna 2300 Tvs]

i have blown up pretty much everything lol it should take the power . i will only be running around 10-12lbs on my 408 so i wont be makin 900hp around 700-750 seems doable and my driveline will take that

[Magna 2300 Tvs]

nevermind i found it . i think the low end from the magna is better for me

[Magna 2300 Tvs]

whats an F1r ?

[Magna 2300 Tvs]

i am thinking about upgrading (again) to the new 2300 tvs from magna . they claim it put 15.5 lbs of boost into a 428 lsx , so i would think it would have no problem puting 10-12 lbs into my 408 ls1 . plus it has the dual heat exchanger instead of single . what do you guys think ? no priceing yet

[Loss Of Boost]

yeah i was talking with magna about the new 2300 tvs they said it could feed 15 lbs into my engine no problem but they dont have a kit for our trucks so it would have to bee custom install which means $$$$$

[Loss Of Boost]

thanks guess i will have to find a smaller pulley

[Loss Of Boost]

here is the cam card , i was told it was a good blower cam . the mp122 is fairly new and i tested the boost with a mechanical guage same result . i would think i should get more than 5.5lbs with that blower and no leaks that i can find

 

 

 

[Loss Of Boost]

i just talked to my engine builder and the crank is pinned

[Loss Of Boost]

i just recently had a new cam installed so maybe thats it . is it hard to take off can i do it in my driveway ? would it run fine other thn the boost or should there be other problems ?

[Loss Of Boost]

how do i check the crank pulley to see if its pinned ?

[Loss Of Boost]

nope not the by pass valve it works fine and i was making about 7.5 lbs of boost before

[Loss Of Boost]

i dont think the belt is slipping seems to consistant for that but i will check the by pass valve

[Loss Of Boost]

i seem to be loosing boost on my maggie . down to 5.5 lbs . my question is where could it go on this blower ? the guage seems to be working fine