[Putting A Ls7 In My Ss]

you can get a ls7 for around 10k i think, but that motor doesnt have enough torque for the sss brick... just go SC

[Tomorrows The Big Day For Me....]

congrats but the modding might stop u know that right

 

got to put that in check from the beginning!!!

[I Ran At The Track Last Night For The First Time Ever]

spinnin' ain't winnin!!!

[1/4 Mile Confusion]

spinning the tires s;ightly makes up for a lower stall,helps the engine rev quicker, and get into its power band quicker

[Took The Yukon To The Track]

i think tracks need to regulate which vehicles get to run....14.99 and below...

[1/4 Mile Confusion]

try higher octane to eliminate it as your problem

[Killed My Friends Subaru Sti]

60 to 80 hp does not make up for the extra 2000 pounds...LOL>

[Put My V Max In The 14s]

what were your 60 ft times 4wd & 2wd? Did you try auto 4wd, dont know how bad it would be for the transfer case

[Wtf?]

I'm not even gonna say it...but I'm sure alot of you are thinking it

 

[Wtf?]

[408 Stroker Kit]

There is really no clearing w/the 408, you jus need to have pistons for the large crank, more specifically piston#8. you do not need to notch the block as with past chevy 350 blocks. Summit racing, has the eagle complete kit for $2200. I believe

 

~Dan

 

 

thanks, good info for when my motor needs a rebuild...had to notch the block when doing my 360/408 dodge stroker

[Sss Vs Srt4]

mopar stage 3 kits produce 310 hp and 325 ft tq with high octane they do 355 hp 365 tq... factory warranty too almost made me want to buy one, but it still is a neon/rental car

[Trans Cooler Install]

for some strange reason i think you should take your truck to a certified tech/ shop for the install...

[The United States Of Toyota]

at the end of the day the tundra will always be a girls truck

chevy for trucks, honda/nissan for cars. wifs drives an 07 civic coupe

[The United States Of Toyota]

there hasn't been an american made CAR that i would ever buy except a corvette

[Career Path, Kinda Wanna Change Directions]

i went to UTI Auto tech school and ended up working on electric forklifts, go-figure!? but its worked out so far in the $ department...

[408 Stroker Kit]

any clearancing involved with the 408?

[408 Stroker Kit]

408? thought that was a mopar # 360/408

how do you get away with only pistons and rods with no crank? under gring it?

[Turbo Motor Smoking Bad]

sounds like you blew a head gasket out toward the oil galley, start with the head. i had a 1.8 turbo jetta and it is common to find oil down into the intercooler.

[Need Some Help/advice With Customizing]

i know a guy who lives hear in so cal who swapped a ls1 into a 98 4dr gmc jimmy and got it to be smog legal,had to take it to the ref. and got a new door sticker, totally legit

[Accumulator Piston]

believe it softens the hydralic forses/ pressure between shifts

[Took The Powerstroke To The Track]

is that in 4 wheel drive?

[Should I?]

just something else to collect dust-downgrade-

[Second Kill]

racing an F-150 is a waste of gas money unless it is a lightning, well that is one more point for team chevrolet

[Alignment Issues]

most likely a poor alignment job, i had a firestone dealer do an alignment on my truck and they left one of the tie rod jam nuts loose, another shop aligned my brothers 2500dmax and told him his rear axle was bent!!! this wasn't true at all, the tech was too lazy and did not properly calibrate the rear tire sensors.